Scotsman MC 45 Wartungshandbuch PDF herunterladen (Seite 27)

Page 27

B. REPLACEMENT OF EVAPORATOR

TEMPERATURE SENSOR (BLUE PLUG)

1. Remove front, left and top panels.

2. Remove the evaporator cover and snap off

the two metal clip securing the sensor probe to

the serpentine.

3. Trace the evaporator sensor terminal plug

on the rear side of the control box and remove it

from its socket by carefully pulling out theterminal

plug securing clip.

4. To install the replacement evaporator sensor

follow the above steps in reverse.

C. REPLACEMENT OF CONDENSER

TEMPERATURE SENSOR (BLACK PLUG)

1. Remove front and left side panels.

2. Trace the condenser sensor probe located

within the condenser fins on air cooled version

and withtrow it.

On water cooled version remove it by opening

the plastic strap (reusable) securing the probe to

the refrigerant liquid line.

3. Trace the condenser sensor terminal plug

on the rear side of the control box and remove it

from its socket by carefully pulling out the terminal

plug securing clip.

4. To install the replacement condenser sensor

follow the above steps in reverse.

D. REPLACEMENT OF AMBIENT

TEMPERATURE SENSOR (RED PLUG)

1. Remove front and left side panels.

2. Trace the ambient sensor probe holded on

its metal bracket in front of the condenser fins-on

air cooled version-and remove it by unloosing its

securing plastic clamp.

On water cooled version, remove it by opening

the plastic strap (reusable) securing the probe on

the water supply line to the condenser.

3. Trace the ambient sensor terminal plug on

the rear side of the control box and remove it from

its socket by carefully pulling out the terminal

plug securing clip.

4. To install the replacement ambient sensor

follow the above steps in reverse.

E. REPLACEMENT OF ICE LEVEL LIGHT

CONTROL (FOUR PINS BLACK PLUG)

1. Remove the front, left and right side panels.

2. Trace the ice level light control terminal plug

(the only one with four terminal pins) on the rear

side of the control box and remove it from its

socket by carefully pulling out the terminal plug

securing clip.

3. Open the Storage Bin door and remove the

ice level light control assy secured to the metal

bracket by unloosing its two securing screws.

4. Remove the PVC plastic plug from unit

base then with traw the entire ice level light

control cable and terminal plug through the hole

in the unit base.

5. To instali the replacement ice level light

control follow the above steps in reverse.

NOTE. Slip in the ice level control cable in the

center of the plastic plug so to avoid any sort

of contact with the unit frame.

F. REPLACEMENT OF P.C. BOARD

1. Remove front and left side panel.

2. Remove all sensor terminal plugs, located

on the rear side of P.C. Board, by carefully

releasing them out from their sockets clips.

3. Disconnect the terminal board connection

plug from the rear side of P.C. BOARD then

unloose the four screws holding the same to the

plastic control box and remove it.

4. To install the replacement P.C. BOARD

follow the above steps on reverse.

G. REPLACEMENT OF THE WATER PUMP

1. Remove front and right side panels.

2. Locate the water pump in the front right

corner of the evaporator chamber.

3. Unloose the screw and the yellow green

ground wire. Trace the pump electrical wire leads

and disconnect them.

4. Remove the two screws securing the pump

to sump tank.

5. Remove the plastic ice chute and through

the ice discharge opening trace the plastic hose

and disconnect it from the port of the pump body.

6. Pull out the pump assy from sump.

7. To install the replacement pump follow the

above steps in reverse.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 36 37

Kommentare zu diesen Handbüchern

Keine Kommentare

Scotsman MC 45 Wartungshandbuch Seite 27

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Eiswürfelmacher Scotsman MC 45