Scotsman CS0415 Wartungshandbuch

Service Manual forCuber Model CS0415

Component LocationJuly 2007Page 10CS0415Service ManualWaterDistributorEvaporatorWater ReturnTubeManual DrainWater ValveOutlet TubeMeasured FillValveBi

Diagnostic ModeDo not continue with the diagnosis of the ice maker if a fuse is blown, a circuit breaker is tripped, or ifthere is less than a 120 vol

Error DisplaysThese errors will occur at any time during normal operation if a thermistor fails.•2 Blinks - Off Light is blinking twice in repeating i

Component TestingBefore testing any of the components, perform the following checks:•Control failure can be the result of corrosion on connectors. The

Water Level Sensor1. Run the diagnostic tests and check for theproper operation of the water level sensor in step4b.2. With the water level sensor imm

Flow Chart - Overall OperationJuly 2007Page 15CS0415Service ManualSwitch OnFlush ModeBeginsFreeze ModeBeginsHarvest ModeBegins, waterdrains and refill

Flow Chart - Freeze Mode DetailsJuly 2007Page 16CS0415Service ManualFreeze ModeWater LevelSensorDetected?Comp., fan motor,spray pump are onWater level

Service DiagnosisJuly 2007Page 17CS0415Service ManualSymptom Possible Cause Probable CorrectionNo ice, not operatingNo power at wall outlet Check circ

Service DiagnosisJuly 2007Page 18CS0415Service ManualSymptom Possible Cause Probable CorrectionWill not make ice. Waterreservoir is full. Evaporator i

Removal and Replacement - ThermistorBin Thermistor and / Or Cutter Grid1. Unplug ice maker or disconnect power.2. Open the ice maker door.3. Cover or

Table of ContentsSpecifications ... Page 3Installation: ... Page 4Test

To remove the evaporator thermistor:a) Remove the cutter grid from the unitb) Disconnect the evaporator thermistor connectorfrom the bottom of the con

1. Unplug ice maker or disconnect power.2. Open the ice maker door.3. Cover or remove the ice from the storage bin.4. Remove the cutter grid cover and

7. Disconnect the water fill tube from the pumpmounting bracket.8. Disconnect the two wire pump connectors fromthe harness block.9. Remove the two thu

Evaporator1. Unplug ice maker or disconnect power.2. Open the ice maker door.3. Remove the ice from the storage bin.4. Remove the cutter grid and the

14. Remove the two screws from the reservoirwater trough and remove the trough.Remove the hex-head screw from the waterpump shield and remove the shie

21. Lift the evaporator and its connecting tubinghigh enough from the unit to access the tubingunderneath.Access the sealed system and discharge there

SCOTSMAN ICE SYSTEMS775 Corporate Woods Parkway, Vernon Hills, IL 60061800-533-6006www.scotsman-ice.com17-3187-01

SpecificationsScotsman Ice Systems are designed andmanufactured with the highest regard for safetyand performance. They meet or exceed thestandards of

Installation:The ice machine is designed to be installedindoors, in a controlled environment. Do not placewhere the temperature limits for air or wate

Test Mode - Ice Thickness AdjustmentThe CS0415 has three push button switches: ON,OFF and CLEAN. These can be used to switch themachine on, off and to

Technical Charts:July 2007Page 6CS0415Service ManualBin ThermistorCut-In Cut-OutTemperature Resistance Temperature ResistanceBin 40oF. +/- 1oF. 25.9k

Operational Modes:There are four main operational modes for the icemaker:•Freeze•Harvest•Clean•Service (Diagnostics)Ice Making CycleIn addition, there

Harvest ModeElectrical SystemWhen the water level in the reservoir drops belowthe water level sensor it signals the electroniccontrol to terminate pow

Component LocationJuly 2007Page 9CS0415Service ManualControllerLight SwitchTransformerEvaporatorCutter GridPush Button SwitchesBinThermistorWater Leve