Scotsman HD150 Handbuch PDF herunterladen

Introduction

To the owner or user: This product manual is a

source of information about the installation, start

up, cleaning, maintenance and repair of the

product.

The HD150 is a hotel/motel ice dispenser. It is

designed to use a Scotsman CME306 or CME456

ice machine as the source for ice.

Ice from the cuber falls into the insulated hopper,

where it is stored until needed. When a user

pushes the dispense button a rotating wheel

scoops the ice up to the top front of the hopper

where there is an outlet to the ice chute.

Table of Contents

Specifications/Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . page 2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3

Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5

Final Check List/Initial Start Up/Electrical Sequence . . . . . . . . . . . . . . . page 7

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8

Service Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9

Removal and Replacement . . . . . . . . . . . . . . . . . . . . . . . . . page 10

Parts lists and wiring diagrams are located in the

center of this manual, printed on yellow paper.

Note the warning symbol where it appears in this

manual. It is an alert for important safety

information on a hazard that might cause serious

injury.

Keep this manual for future reference.

This manual was printed on recycled paper.

HD150

May 2000

Page 1

1 2 3 4 5 6 ... 10 11

Inhaltsverzeichnis

Seite 1 - Introduction

IntroductionTo the owner or user: This product manual is asource of information about the installation, startup, cleaning, maintenance and repair of t

Seite 2 - Specifications:

Service DiagnosisPROBLEM POSSIBLE CAUSE PROBABLE FIXDoes not vend No ice Check ice machineNo power Check power supplyVend switch open Check/replace ve

Seite 3 - Installation: General

Removal and Replacement: HD150-1Gear Motor1. Disconnect electrical power2. Locate key and remove sink.3. Trace wires from gearmotor to control box and

Seite 4 - Installation: Ice Machine

Specifications:Limitations:•Must meet the same limitations as the cuberinstalled on top of it:550F. air minimum,1000F. air maximum.•Must be installed

Seite 5 - Kits: Coin Mechanism (KSLDC2)

Installation: GeneralAfter the carton has been removed from thedispenser, the legs may be installed.Place flat portions of the carton on the floor beh

Seite 6

Installation: Ice MachineCheck that gasket tape has been placed at theoutside edge of the dispenser top.There is no thermostat to install. Place the i

Seite 7 - Electrical Sequence

Kits: Coin Mechanism (KSLDC2)A kit is available to install a coin mechanism, andanother kit is available to install a room keymechanism. Both come wit

Seite 8 - Operational Schematic

Key Kit Installation: (KSLDK2)1. Disconnect electrical power2. Remove sink and drain pan.3. Remove cover.4. Remove control box cover5. From kit, locat

Seite 9 - Cleaning

Final Check List/Initial Start Up1. Check that electrical power has been supplied.2. Check that a drain, separate from the icemachine, insulated and m

Seite 10 - Service Diagnosis

Operational SchematicIce MachineIce ChuteGear MotorSinkDrain PanCondensate PanDrainStorage BinHD150May 2000Page 8

Seite 11 - May 2000

CleaningGeneral Care and CleaningPeriodically inspect and clean the ice dispenser tokeep it operating at peak performance.Wash the outside of the disp