Scotsman FME2400RH Wartungshandbuch

TO THE OWNER OR USER:The service manual you are reading is intended toprovide you, and the maintenance or servicetechnician, with the information need

COMPONENT DESCRIPTION: EvaporatorEvaporator: A refrigerated vertical tube filled waterand containing a water seal and auger.Auger: A solid stainless s

ELECTRICAL SEQUENCERefer the wiring diagram as needed.Each system is separateIf the machine is switched off at the master switch,but is otherwise read

OPERATIONWaterWater enters the machine through the 3/8" maleflare at the rear of the cabinet, goes to the waterreservoir which it enters through

OPERATION: RefrigerationThe remote high sidesupplies high pressureliquid refrigerant to theliquid line connection onthe ice machine. Afterthe sight gl

MAINTENANCE AND CLEANINGA Scotsman Ice System represents a sizable investment of time and money in any company’s business. Inorder to receive the bes

MAINTENANCE1. The bin control uses devices that sense light,therefore they must be kept clean enough so thatthey can “see”. At least twice a year, rem

CLEANINGIn some installations the water supply to the icemaker will be so concentrated with dissolvedminerals, (such as calcium carbonate) that as ic

SERVICE DIAGNOSIS: Condition - No Ice Being ProducedSTATUS: NOTHING OPERATESA. Check: Voltage to the unit, restore it if there is none. Compare to the

WATER RESERVOIR1. Shut off the water supply to the ice maker.2. Remove front panel and reservoir cover.3. To removefloat only, disconnect water inlett

REMOVAL AND REPLACEMENT: Bearing And BreakerNote: Removal of the auger, water seal,evaporator and gearmotor must begin at the top ofthe assembly.To Re

FOR THE INSTALLER: SpecificationsThe FME2400RH is designed to fit the Scotsmanstorage bins BH800 or B90. Leg kit KLP4 isrecommended when using both th

To Remove the Auger:Turn off the water to the machine, and unclip theevaporator drain hose, pull it down and drain theevaporator into the bin or a con

To Remove the Water Seal:(Assuming all steps to remove the auger havebeen performed.)1. The gearmotor/evaporator assembly will have tobe exposed.2. Re

To Replace the Evaporator:(Assuming all the steps for removal of the thrustbearing, breaker, auger, and water seal have beenperformed.)1. Shut the han

To RemoveandRepairthe GearmotorAssembly:(Assuming thattheproceduresthroughremovalofthewatersealhave beenperformed.)1.Removetheelectricalwiresfromthe g

These procedures require the machine to be connected to the power supply. The voltages of theelectronic circuit are very low, but HIGHER VOLTAGES ARE

FOR THE INSTALLERSelect the Location:The unit can only be installed indoorswithin the limitations described onpage 2.The ice machine will have to beco

FOR THE ELECTRICIANCONFORM TO ALL APPLICABLE CODESElectrical Connections:Locate the nameplate for the currentrequirements, and then determine thewire

FOR THE PLUMBERCONFORM TO ALL APPLICABLE CODESWater Supply:The recommended water supply line is 3/8" O.D.copper tubing, with a minimum operation

FOR THE INSTALLER: Final Check List1. Is the unit installed where the air and watertemperatures are within and will remain within thelimitations for t

INITIAL START UP1. Remove the top and front panels.2. Open the water valve, and observe that the twofloat reservoirs fill up with water and shut off.3

COMPONENT IDENTIFICATIONLiquid line valve(s)These valves operate to turn the ice makingprocess on and off.When the ice level drops in the ice chute, t

COMPONENT DESCRIPTION: Control BoxCircuit Board: Controlling the ice machine throughsensors and relays. The sensors are: ice level, andwater level. Th