Scotsman C1848R Bedienungsanleitung

Installation andUser's ManualModels C1448R, C1848R, C2148R

For The Installer: Remote CondenserLocate the condenser as near as possible to theinterior location of the ice machine.Note: The location of the conde

Precharged Line RoutingDo not connect the precharged tubing until allrouting and forming of the tubing is complete. Seethe Coupling Instructions for f

Coupling InstructionsThe couplings on the ends of the pre-charged linesets are self-sealing when installed properly.Follow these instructions carefull

Plumbing RequirementsAll models require connection to cold, potablewater. A hand actuated valve within site of themachine is required. There is a sing

DrainsAll models require drain tubing to be attached tothem. There is a single ¾” FPT drain fitting in theback of the cabinet.Install new tubing when

ElectricalThe machine is not supplied with a power cord, onemust either be field installed or the machinehard-wired.The dataplate on the back of the c

Final Check List:1. Is the unit located indoors in a controlledenvironment?2. Is the unit located where it can receiveadequate cooling air?3. Has the

Initial Start Up1. Remove front and left side panels. Checkmachine for any packing or wires rubbingmoving parts. Note location of control board inuppe

AdjustmentsBridge Thickness - For A Service Tech Only1. Push and hold Off till the machine stops.2. Remove evaporator cover.3. Remove curtain.4. Use a

Use and OperationOnce started, the ice machine will automaticallymake ice until the bin or dispenser is full of ice.When ice level drops, the ice mach

IntroductionThe design of this modular remote cuber is theresult of years of experience with remote icemachine refrigeration systems. Standard feature

SwitchesThere's front access to two switches – on and off.To switch the machine OFF, push and release theOff button. The machine will shut off at

Options and Other InformationSmartBoardWhen this option is present there is an additionaldisplay panel in the area below the main controlboard. It is

Cleaning, Sanitation and MaintenanceThis ice system requires three types ofmaintenance:•Remove the build up of mineral scale from the ice machine’s wa

13. Remove water distributors from ice machine.Inspect distributors for restricted orifice holes,including those in the inner tube. Be sure allholes a

Remote condenserThe condenser fins will need to be cleaned.Push and release the Off button. Wait until themachine stops.Note: Lock out the controller

What to do before calling for serviceReasons the machine might shut itself off:•Lack of water.•Freeze cycle takes too long.•Harvest cycle takes too lo

SCOTSMAN ICE SYSTEMS775 Corporate Woods Parkway, Vernon Hills, IL 60061800-533-6006www-scotsman-ice.com17-3083-04

Installation: Product SpecificationsLocation LimitationsThis ice system is made up of three parts, the icemaking machine, or head; the remote condense

Model Number DescriptionExample•C1448SR-32A•C=cuber•14=nominal capacity in 100s of pounds•48=nominal width of cabinet in inches•S=cube size, S=small o

Product Description and Electrical Requirements*Or HACR circuit breakers.Table notes: Medium cube models have the sameelectrical characteristics as Sm

Condenser and Ice Machine LayoutsNovember 2006Page 5C1448, C1848, C2148Remote Condenser Models - User Manual.88 DIA. ELECTRICALINLET.65 in1.7 cm27.56

WaterThe quality of the water supplied to the ice machinewill have an impact on the time between cleaningsand ultimately on the life of the product. T

Panel Removal1. Locate and loosen the two screws at the frontedge of the top panel.2. Pull the front panel out at the top until itclears the top panel

Remote Condenser LocationUse the following for planning the placement of thecondenser relative to the ice machineLocation Limits - condenser location